| Zvikomborero VIncent Zvikaramba | a25011a | 2016-07-21 16:32:35 -0400 | [diff] [blame^] | 1 | ######################################## |
| 2 | # NLP/WIFI positioning options bit mask |
| 3 | ######################################## |
| 4 | # Enable NLP fixes for WIPER/ODCPI feature => WIPER = 0x1 |
| 5 | # Enable free wifi scan injections for GEOFENCE => FREE_WIFI = 0x2 |
| 6 | # Enable SUPL2 MLD wifi => SUPL_WIFI = 0x4 |
| 7 | # Enable Attached Wifi AP info injection for GEOFENCE => FREE_AP_INFO = 0x8 |
| 8 | # default = WIPER | FREE_WIFI | SUPL_WIFI | FREE_AP_INFO |
| 9 | NLP_WIFI_LISTENER_MODE = 0 |
| 10 | |
| 11 | ################################################## |
| 12 | # Select WIFI Wait Timeout value in seconds for SUPL |
| 13 | ################################################## |
| 14 | WIFI_WAIT_TIMEOUT_SELECT = 0 |
| 15 | |
| 16 | ################################ |
| 17 | # NLP Settings |
| 18 | ################################ |
| 19 | # NLP_MODE 1: GNP Only, 2: QNP Only, 3: Combo |
| 20 | # NLP_TOLERANCE_TIME_FIRST: Time in ms used in Combo mode |
| 21 | # to determine how much Tolerance for first position |
| 22 | # NLP_TOLERANCE_TIME_AFTER: Time in ms used in Combo mode |
| 23 | # to determine how much Tolerance for positions after first |
| 24 | # NLP_THRESHOLD: Sets how many failures needed before |
| 25 | # switching preferred NLP in Combo mode |
| 26 | # NLP_ACCURACY_MULTIPLE: Determines how far off the accuracy |
| 27 | # must be, in multiples, between two NLP location reports to |
| 28 | # be considered much worse accuracy. Used in switching logic |
| 29 | NLP_MODE = 1 |
| 30 | NLP_TOLERANCE_TIME_FIRST = 5000 |
| 31 | NLP_TOLERANCE_TIME_AFTER = 20000 |
| 32 | NLP_THRESHOLD = 3 |
| 33 | NLP_ACCURACY_MULTIPLE = 2 |
| 34 | |
| 35 | # Threshold period for ZPP triggers |
| 36 | ZPP_TRIGGER_THRESHOLD=10000 |
| 37 | |
| 38 | ################################### |
| 39 | # GEOFENCE SERVICES |
| 40 | ################################### |
| 41 | # If set to one of the defined values below, it will override |
| 42 | # the responsiveness for geofence services, which implements |
| 43 | # the Proximity Alert API. If not set to a value defined below, |
| 44 | # which is default, it will not override the responsivness. |
| 45 | # The geofence HAL API is unaffected by this value. |
| 46 | # GEOFENCE_SERVICES_RESPONSIVENESS_OVERRIDE Values: |
| 47 | # 1: LOW responsiveness |
| 48 | # 2: MEDIUM responsiveness |
| 49 | # 3: HIGH responsiveness |
| 50 | GEOFENCE_SERVICES_RESPONSIVENESS_OVERRIDE = 0 |
| 51 | |
| 52 | ##################################### |
| 53 | # IZAT PREMIUM FEATURE SETTINGS |
| 54 | ##################################### |
| 55 | #Possible states of a feature: |
| 56 | #DISABLED |
| 57 | #BASIC |
| 58 | #PREMIUM |
| 59 | |
| 60 | #GTP_CELL_PROC valid options: |
| 61 | # AP |
| 62 | # MODEM |
| 63 | GTP_CELL_PROC=MODEM |
| 64 | |
| 65 | #GTP_CELL valid modes: |
| 66 | # DISABLED |
| 67 | # BASIC |
| 68 | GTP_CELL=BASIC |
| 69 | |
| 70 | #GTP_WIFI valid modes: |
| 71 | # DISABLED |
| 72 | # BASIC |
| 73 | GTP_WIFI=BASIC |
| 74 | |
| 75 | #SAP valid modes: |
| 76 | # DISABLED |
| 77 | # BASIC |
| 78 | # PREMIUM |
| 79 | SAP=BASIC |
| 80 | |
| 81 | #PIP valid modes: |
| 82 | # DISABLED |
| 83 | # PREMIUM |
| 84 | PIP=DISABLED |
| 85 | |
| 86 | ##################################### |
| 87 | # Location process launcher settings |
| 88 | ##################################### |
| 89 | |
| 90 | #Values for PROCESS_STATE: |
| 91 | # ENABLED |
| 92 | # DISABLED |
| 93 | |
| 94 | #FEATURE MASKS: |
| 95 | # GTP-WIFI 0X03 |
| 96 | # GTP-CELL 0X0c |
| 97 | # PIP 0x30 |
| 98 | # SAP 0Xc0 |
| 99 | |
| 100 | #Values for PLATFORMS can be: |
| 101 | #1. Any valid values obtained from ro.board.platform separated by single space. For example: msm8960 msm8226 |
| 102 | #2. all -> for All platforms |
| 103 | |
| 104 | #Values for BASEBAND can be: |
| 105 | #1. Any valid values obtained from ro.baseband separated by single space. For example: sglte sglte2 |
| 106 | #2. all -> for all basebands |
| 107 | |
| 108 | PROCESS_NAME=/system/bin/gpsone_daemon |
| 109 | PROCESS_STATE=DISABLED |
| 110 | PROCESS_GROUPS=inet net_raw |
| 111 | PREMIUM_FEATURE=0 |
| 112 | IZAT_FEATURE_MASK=0 |
| 113 | PLATFORMS=msm7630_fusion |
| 114 | BASEBAND=svlte2a sglte sglte2 |
| 115 | |
| 116 | PROCESS_NAME=/system/bin/location-mq |
| 117 | PROCESS_STATE=ENABLED |
| 118 | PROCESS_GROUPS=gps |
| 119 | PREMIUM_FEATURE=1 |
| 120 | IZAT_FEATURE_MASK=0x3f |
| 121 | PLATFORMS=all |
| 122 | BASEBAND=all |
| 123 | |
| 124 | PROCESS_NAME=/system/bin/lowi-server |
| 125 | PROCESS_STATE=ENABLED |
| 126 | PROCESS_GROUPS=gps net_admin wifi inet qcom_diag net_raw |
| 127 | PREMIUM_FEATURE=1 |
| 128 | IZAT_FEATURE_MASK=0x33 |
| 129 | PLATFORMS=all |
| 130 | BASEBAND=all |
| 131 | |
| 132 | PROCESS_NAME=/system/bin/quipc_igsn |
| 133 | PROCESS_STATE=ENABLED |
| 134 | PROCESS_GROUPS=inet gps qcom_diag |
| 135 | PREMIUM_FEATURE=1 |
| 136 | IZAT_FEATURE_MASK=0x30 |
| 137 | PLATFORMS=all |
| 138 | BASEBAND=all |
| 139 | |
| 140 | PROCESS_NAME=/system/bin/quipc_main |
| 141 | PROCESS_STATE=ENABLED |
| 142 | PROCESS_GROUPS=gps net_admin wifi inet qcom_diag |
| 143 | PREMIUM_FEATURE=1 |
| 144 | IZAT_FEATURE_MASK=0x30 |
| 145 | PLATFORMS=all |
| 146 | BASEBAND=all |
| 147 | |
| 148 | PROCESS_NAME=/system/bin/xtwifi-inet-agent |
| 149 | PROCESS_STATE=ENABLED |
| 150 | PROCESS_GROUPS=inet gps |
| 151 | PREMIUM_FEATURE=1 |
| 152 | IZAT_FEATURE_MASK=0x0f |
| 153 | PLATFORMS=all |
| 154 | BASEBAND=all |
| 155 | |
| 156 | PROCESS_NAME=/system/bin/xtwifi-client |
| 157 | PROCESS_STATE=ENABLED |
| 158 | PROCESS_GROUPS=net_admin wifi inet gps |
| 159 | PREMIUM_FEATURE=1 |
| 160 | IZAT_FEATURE_MASK=0x0f |
| 161 | PLATFORMS=all |
| 162 | BASEBAND=all |
| 163 | |
| 164 | PROCESS_NAME=/system/bin/gsiff_daemon |
| 165 | PROCESS_STATE=ENABLED |
| 166 | PROCESS_GROUPS=gps net_raw misc qcom_oncrpc |
| 167 | PREMIUM_FEATURE=1 |
| 168 | IZAT_FEATURE_MASK=0xf0 |
| 169 | PLATFORMS=all |
| 170 | BASEBAND=all |