Added WORKING gprimeltecan device tree.
diff --git a/wifi/WCNSS_qcom_cfg.ini b/wifi/WCNSS_qcom_cfg.ini
new file mode 100644
index 0000000..389b3a6
--- /dev/null
+++ b/wifi/WCNSS_qcom_cfg.ini
@@ -0,0 +1,481 @@
+# This file allows user to override the factory
+
+# defaults for the WLAN Driver
+
+
+# Enable IMPS or not
+gEnableImps=1
+
+# Enable/Disable Idle Scan
+
+gEnableIdleScan=0
+
+# Enable/Disable vsta based on MAX Assoc limit
+gEnableVSTASupport=1
+
+
+# Increase sleep duration (seconds) during IMPS
+# 0 implies no periodic wake up from IMPS. Periodic wakeup is
+# unnecessary if Idle Scan is disabled.
+gImpsModSleepTime=0
+
+
+# Enable BMPS or not
+gEnableBmps=1
+
+# Enable suspend or not
+
+# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
+
+gEnableSuspend=3
+
+# Phy Mode (auto, b, g, n, etc)
+# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
+gDot11Mode=0
+
+
+# CSR Roaming Enable(1) Disable(0)
+
+gRoamingTime=0
+
+
+# Assigned MAC Addresses - This will be used until NV items are in place
+
+# Each byte of MAC address is represented in Hex format as XX
+
+Intf0MacAddress=000AF58989FF
+Intf1MacAddress=000AF58989FE
+Intf2MacAddress=000AF58989FD
+
+Intf3MacAddress=000AF58989FC
+
+
+# UAPSD service interval for VO,VI, BE, BK traffic
+
+InfraUapsdVoSrvIntv=0
+
+InfraUapsdViSrvIntv=0
+
+InfraUapsdBeSrvIntv=0
+
+InfraUapsdBkSrvIntv=0
+
+# Flag to allow STA send AddTspec even when ACM is Off
+gAddTSWhenACMIsOff=1
+
+# Make 1x1 the default antenna configuration
+
+gNumRxAnt=1
+
+
+# Beacon filtering frequency (unit in beacon intervals)
+
+gNthBeaconFilter=50
+
+
+# Enable WAPI or not
+
+# WAPIIsEnabled=0
+
+
+# Flags to filter Mcast abd Bcast RX packets.
+
+# Value 0: No filtering, 1: Filter all Multicast.
+
+# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
+
+McastBcastFilter=2
+
+
+#Flag to enable HostARPOffload feature or not
+
+hostArpOffload=1
+
+
+#Flag to enable HostNSOffload feature or not
+hostNSOffload=0
+
+#SoftAP Related Parameters
+
+# AP MAc addr
+
+gAPMacAddr=000AF589dcab
+
+
+# 802.11n Protection flag
+
+gEnableApProt=1
+
+
+#Enable OBSS protection
+
+gEnableApOBSSProt=0
+
+
+#Enable/Disable UAPSD for SoftAP
+
+gEnableApUapsd=0
+
+
+# Fixed Rate
+
+gFixedRate=0
+
+
+# Maximum Tx power
+
+# gTxPowerCap=30
+
+
+# Fragmentation Threshold
+
+# gFragmentationThreshold=2346
+
+
+# RTS threshold
+
+RTSThreshold=2347
+
+
+# Intra-BSS forward
+
+gDisableIntraBssFwd=0
+
+
+# WMM Enable/Disable
+
+WmmIsEnabled=0
+
+
+# 802.11d support
+
+g11dSupportEnabled=0
+
+# 802.11h support
+g11hSupportEnabled=1
+
+# ESE Support and fast transition
+EseEnabled=1
+ImplicitQosIsEnabled=0
+gNeighborScanTimerPeriod=200
+
+gNeighborLookupThreshold=76
+gNeighborReassocThreshold=81
+
+gNeighborScanChannelMinTime=20
+gNeighborScanChannelMaxTime=30
+gMaxNeighborReqTries=3
+
+# Legacy (non-ESE, non-802.11r) Fast Roaming Support
+# To enable, set FastRoamEnabled=1
+# To disable, set FastRoamEnabled=0
+FastRoamEnabled=1
+
+#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
+#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
+#the RSSI of the new/roamable AP should be for roaming
+RoamRssiDiff=5
+
+#SAP Country code
+
+# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
+
+# Example
+
+# US Indoor, USI
+
+# Korea Outdoor, KRO
+
+# Japan without optional byte, JP
+
+# France without optional byte, FR
+
+#gAPCntryCode=USI
+
+
+#Short Guard Interval Enable/disable
+
+gShortGI20Mhz=1
+
+gShortGI40Mhz=1
+
+
+#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
+
+gAPAutoShutOff=0
+
+
+# SAP auto channel selection configuration
+
+# 0 = disable auto channel selection
+
+# 1 = enable auto channel selection, channel provided by supplicant will be ignored
+
+gApAutoChannelSelection=0
+
+
+# Listen Energy Detect Mode Configuration
+
+# Valid values 0-128
+
+# 128 means disable Energy Detect feature
+
+# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
+
+# 10-128 are reserved.
+
+# The EDET threshold mapping is as follows in 3dB step:
+
+# 0 = -60 dBm
+
+# 1 = -63 dBm
+
+# 2 = -66 dBm
+
+# ...
+
+# 7 = -81 dBm
+
+# 8 = -84 dBm
+
+# 9 = -87 dBm
+
+# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
+
+#
+
+# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
+
+#
+
+gEnablePhyAgcListenMode=128
+
+
+#Preferred channel to start BT AMP AP mode (0 means, any channel)
+
+BtAmpPreferredChannel=0
+
+
+#Preferred band (both or 2.4 only or 5 only)
+
+BandCapability=0
+
+
+#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
+
+enableBeaconEarlyTermination=1
+
+beaconEarlyTerminationWakeInterval=11
+
+#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
+
+gEnableBtAmp=0
+
+
+#SOFTAP Channel Range selection
+
+gAPChannelSelectStartChannel=1
+
+gAPChannelSelectEndChannel=11
+
+
+#SOFTAP Channel Range selection Operating band
+
+# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
+
+gAPChannelSelectOperatingBand=0
+
+
+#Channel Bonding
+gChannelBondingMode5GHz=1
+
+
+#Enable Keep alive with non-zero period value
+
+gStaKeepAlivePeriod=30
+
+
+#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
+#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
+#For both active and power save clients.
+
+#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
+#If doesn't honor for 5 seconds then DUT remove client.
+
+#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
+#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
+#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
+
+#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
+#where we send NULL frame.
+
+gApLinkMonitorPeriod=30
+
+gGoLinkMonitorPeriod=10
+
+#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
+#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
+
+gGoKeepAlivePeriod=3
+
+gApKeepAlivePeriod=10
+
+
+#If set will start with active scan after driver load, otherwise will start with
+
+#passive scan to find out the domain
+
+gEnableBypass11d=1
+
+
+#If set to 0, will not scan DFS channels
+
+gEnableDFSChnlScan=1
+
+
+gVhtChannelWidth=2
+gEnableLogp=1
+
+
+# Enable Automatic Tx Power control
+
+gEnableAutomaticTxPowerControl=0
+
+# 0 for OLPC 1 for CLPC and SCPC
+gEnableCloseLoop=1
+
+#Data Inactivity Timeout when in powersave (in ms)
+gDataInactivityTimeout=200
+
+# VHT Tx/Rx MCS values
+# Valid values are 0,1,2. If commented out, the default value is 0.
+# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
+gVhtRxMCS=2
+gVhtTxMCS=2
+
+
+#If set to 0, MCC is not allowed.
+gEnableMCCMode=1
+
+# 1=enable STBC; 0=disable STBC
+gEnableRXSTBC=1
+
+# Enable Active mode offload
+gEnableActiveModeOffload=1
+
+#Enable Scan Results Aging based on timer
+#Timer value is in seconds
+#If Set to 0 it will not enable the feature
+gScanAgingTime=0
+
+#Enable Power saving mechanism Based on Android Framework
+#If set to 0 Driver internally control the Power saving mechanism
+#If set to 1 Android Framwrok control the Power saving mechanism
+isAndroidPsEn=0
+
+#disable LDPC in STA mode if the AP is TXBF capable
+gDisableLDPCWithTxbfAP=1
+
+#Enable thermal mitigation
+gThermalMitigationEnable=1
+
+gEnableFastRoamInConcurrency=1
+
+#List of Country codes for which 11ac needs to be disabled
+#Each country code must be delimited by comma(,)
+gListOfNon11acCountryCode=RU,UA,ZA
+
+#Maxium Channel time in msec
+gMaxMediumTime = 5480
+
+# 802.11K support
+gRrmEnable=1
+gRrmOperChanMax=8
+gRrmNonOperChanMax=8
+gRrmRandIntvl=100
+
+#Scan offload
+gEnableDirectedScanOffload=0
+
+#FlexConnect Power Factor
+#Default is set to 0 (disable)
+gFlexConnectPowerFactor=0
+
+#SAP/P2P-GO mode traffic monitor
+gEnableTrafficMonitor=1
+gTrafficIdleTimeout=3000
+
+#Disable/Enable Strict FCC Regulatory
+# 0 to disable, 1 to enable
+gEnableStrictRegulatoryForFCC=1
+
+#Enable/Disable Modulated DTIM feature
+gEnableModulatedDTIM=3
+
+#max LI value for modulated DTIM
+gMaxLIModulatedDTIM=3
+
+#Enable/Disable Link Layer Statistics Feature
+gEnableLLStats=1
+
+#Enable/Disable EXTScan Feature
+gEnableEXTScan=1
+
+# Enable/Disable Mcast addr list filtering
+# isMcAddrListFilter deprecated
+gMCAddrListEnable=1
+
+# TDLS setting
+gEnableTDLSSupport=1
+gEnableTDLSImplicitTrigger=1
+gEnableTDLSBufferSta=0
+gTDLSMaxDiscoveryAttempt=5
+gTDLSIdleTimeout=10000
+
+# Country code priority
+gCountryCodePriority=1
+
+#blocking SCO rate as 0% from 1%
+btcMaxScoBlockPerc=0
+
+# Scan Timing Parameters
+gActiveMaxChannelTime=80
+gActiveMinChannelTime=60
+
+#Enable Scan Results Aging based on number of scans
+gScanResultAgeCount=1
+
+#To enable CTS2S during SCO in WCN cfg ini
+btcCTS2SduringSCO=1
+
+#BTC OPP+SAP/GO configuration
+btcSapActiveWlanLen=35000
+btcSapActiveBtLen=20000
+
+#BTC BT paging configuration
+btcStaticLenPageBt=135000
+btcStaticLenPageWlan=15000
+
+#BT_OPP+STA coex configuration WLAN 35ms/BT_OPP 30ms
+btcActiveWlanLen=35000
+btcActiveBtLen=30000
+
+#change the value of heart threat time
+gHeartbeat24=60
+
+#Disable Preferred Network Offload feature
+gPNOScanSupport=0
+
+# Roam Scan offload
+gRoamScanOffloadEnabled=1
+
+# For p2p device's DTIM policy
+gIgnoreDynamicDtimInP2pMode=1
+
+# Ignore frames with less signal strength than a defined value
+gAthDisable=1
+
+END
+
+# Note: Configuration parser would not read anything past the END marker
+