#Uncommenting these urls would only enable
#the power up auto injection and force injection(test case).
XTRA_SERVER_1=http://xtrapath1.izatcloud.net/xtra3grc.bin
XTRA_SERVER_2=http://xtrapath2.izatcloud.net/xtra3grc.bin
XTRA_SERVER_3=http://xtrapath3.izatcloud.net/xtra3grc.bin

#Version check for XTRA
#DISABLE = 0
#AUTO    = 1
#XTRA2   = 2
#XTRA3   = 3
XTRA_VERSION_CHECK=0

# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0

#Test
NTP_SERVER=time.izatcloud.net
#Asia
# NTP_SERVER=asia.pool.ntp.org
#Europe
# NTP_SERVER=europe.pool.ntp.org
#North America
# NTP_SERVER=north-america.pool.ntp.org

# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
#               4 - Debug, 5 - Verbose
# If DEBUG_LEVEL is commented, Android's logging levels will be used
DEBUG_LEVEL = 4

# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0

# Below bit mask configures how GPS functionalities
# should be locked when user turns off GPS on Settings
# Set bit 0x1 if MO GPS functionalities are to be locked
# Set bit 0x2 if NI GPS functionalities are to be locked
# default - non is locked for backward compatibility
#GPS_LOCK = 0

# supl version 1.0
SUPL_VER=0x10000

# Emergency SUPL, 1=enable, 0=disable
SUPL_ES=0
# Sensor R&D : Non-SUPL ES should be default

#Choose PDN for Emergency SUPL
#1 - Use emergency PDN
#0 - Use regular SUPL PDN for Emergency SUPL
USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=1

#SUPL_MODE is a bit mask set in config.xml per carrier by default.
#If it is uncommented here, this value will over write the value from
#config.xml.
#MSA=0X2
#MSB=0X1
#Sensor R&D : Change default bit mask
SUPL_MODE=3

# GPS Capabilities bit mask
# SCHEDULING = 0x01
# MSB = 0x02
# MSA = 0x04
# ON_DEMAND_TIME = 0x10
# GEOFENCE = 0x20
# default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING | GEOFENCE
CAPABILITIES=0x37

# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000

################################
##### AGPS server settings #####
################################

# FOR SUPL SUPPORT, set the following
# SUPL_HOST=supl.host.com or IP
# SUPL_PORT=1234

# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234

# Bitmask of slots that are available
# for write/install to, where 1s indicate writable,
# and the default value is 0 where no slots
# are writable. For example, AGPS_CERT_WRITABLE_MASK
# of b1000001010 makes 3 slots available
# and the remaining 7 slots unwritable.
#AGPS_CERT_WRITABLE_MASK=0

####################################
#  LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default)
# 1: Enable LPP_User_Plane on LTE
# 2: Enable LPP_Control_Plane
# 3: Enable both LPP_User_Plane and LPP_Control_Plane
LPP_PROFILE = 0 # Sensor R&D : This will not be injected to MODEM

################################
# EXTRA SETTINGS
################################
# NMEA provider (1=Modem Processor, 0=Application Processor)
NMEA_PROVIDER=1
# Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE)
SGLTE_TARGET=0

##################################################
# Select Positioning Protocol on A-GLONASS system
##################################################
# 0x1: RRC CPlane
# 0x2: RRLP UPlane
# 0x4: LLP Uplane
A_GLONASS_POS_PROTOCOL_SELECT = 0 #Sensor R&D : This will not be injected to MODEM

##################################################
# Delete only Ephemeris files
##################################################
#0 : off - default
#1 : on - Erase only eph files when we use 'delete aiding data' function.
DEL_EPH_ONLY = 0